stylpro WAVELENGTH PRO 5in1 LED MASK

Directions

CHARGING:
Insert the USB-C cable (provided) into the port at the bottom of the controller. Attach to a USB-C friendly power source. The battery icon will show a loading sequence when charging. The remove cannot be used while charging. To enable fast-charging, use at least a 3A power supply.
BEFORE USE:
1. Perform a patch test by placing the mask over your arm and using it on the desired setting for 5-minutes. If up to 10-minutes after the test, your skin has not reacted then continue to use the mask.

HOW TO ASSEMBLE:
The LED Mask will come pre-assembled in Face mode. However, if the eye comfort pads become dislodged and the straps are loose here is how to assemble.
1. Unclip the fasteners on the side of the mask.
2. Place the eye comfort pads into the eye holes. See ‘R' for right eye and ‘L' for left eye on the eye comfort pads.
3. Once the eye comfort pads are in position, clip into the top face fastener. Ensure eye comfort pads are securely attached.
4. Insert each of the straps into the top strap holes. Ensuring that the straps is securely stuck to the velcro on the outside surface of the mask.

HOW TO USE:
Face:
1. Ensure the right and left straps are attached, and the eye protection pads are securely placed into the eye holes.
2. To adjust the size of the LED Mask, use the face fasteners. Always start on the top face fastener, and move to the bottom fastener to loosen the fit if needed.
3. Place the LED Mask onto your face and securely attach the straps around the crown of your head.
4. Long press the power/function button to turn on the LED Mask.
5. To ensure the Face function is selected - short press the 'power/function' button until the 'Face' icon appears on the top panel of your remote.
6. To select your desired mode, short-press the 'Mode' button. To find out which mode is best suited for you, please see our 'MODES' breakdown below.
7. Once you have selected your desired mode, enjoy a 10-15 minute session.
8. To turn off your LED Mask before you have completed your session, long-press the power/function button.

Neck, Chest & Back:
1. Unclip the fasteners and remove the eye protection pads whilst ensuring the right and left straps are attached to the LED Mask.
2. Front of neck and chest: place the LED Mask onto your chest and securely attach the straps around the back of your neck. Allow the LED Mask to rest on your collarbones and chest.
3. Back of neck and upper back: place the LED Mask onto your upper back and securely attach the straps around the front of your neck. Allow the LED Mask to rest on the back of your neck and upper back. Top Tip: for a comfortable fit, allow the straps to lay below your neck.
4. Long press the power/function button to turn on the LED Mask.
5. To ensure the Neck, Chest & Back function is selected - short press the 'power/function' button until the 'Neck' icon appears on the top panel of your remote.
6. To select your desired mode, short-press the 'Mode' button. To find out which mode is best suited for you, please see our 'MODES' breakdown below.
7. Once you have selected your desired mode, enjoy a 12 minute session.
8. To turn off your LED Mask before you have completed your session, long-press the power/function button.

Hair:
1. Unclip the fasteners and remove the eye protection pads whilst ensuring the right and left straps are attached to the LED Mask.
2. Clip the fasteners into the hair fasteners located at the top of the mask. This will allow the mask to form into a 'dome' shape.
3. Turn the LED Mask upside-down to ensure the smaller STYLPRO logo is now facing upright.
4. Place the LED Mask onto your head and securely attach the straps around the back of your head/upper neck. Ensure the mask is covering your front hairline.
5. Long press the power/function button to turn on the LED Mask.
6. To ensure the Hair function is selected - sh

Ingredients

1x STYLPRO Wavelength Pro 5-in-1 LED Mask (pre-assembled with Eye Comfort Pads and Adjustable Straps)
1x LED Mask Controller
1x USB-C Charging Cable
1x Protective Bag